How long does it typically take y'all to turn a pot and striker combo? Right now from cutting my blanks to finished products I'm right at two hours. I'm about to buy a second chuck to hopefully speed this up some. I cut my blanks from rough boards I buy from a man locally.
Sent from my SM-N920V using Tapatalk
Same here, about 2hrs to turn a call and striker start to finish. That's after I've cut my blanks. I usually spend a day or two a month just cutting and organizing blanks so that once I decide what to make it's all already laid out and cut and organized.
I have dowel blanks separated, handle blanks drilled and separated, and call blanks cut and separated.
From grabbing them off the shelf to completely finished, 2 hours.
i would say if i had cut a blank drill it turn it right round 45 minutes ,,,, i never realy do more then 4 or 5 pots at a time,,,, i also have 20 or 30 blanks cut and pre drilled that way when i do get spare time to turn its matters just chucking a blank up ,,, if i have limited time maybe hour thats when i cut and drill
to me its not about the speed i can put a call out !! for me its the enjoyment of doing it see what i can find figure wise in next piece wood
Dang mike your a speed demon.
Sent from my SM-N920V using Tapatalk
The finish on pot and gluing up is 2to4 day process... fast part is making pot and striker
Quote from: Daddy rat on March 12, 2018, 01:42:10 PM
The finish on pot and gluing up is 2to4 day process... fast part is making pot and striker
For sure. I was talking purly about the turning part. I agree with you. Once its turned I usually spend a day on layering finished then my soundboard dries for a day then my playing surface dries for a day. I'd rather wait for the glue to fully dry than rush it out.
Sent from my SM-N920V using Tapatalk
I have about 2 hrs in a call, start to finish, Mike
Yeah it's 2 hr deal turning pot and striker and then sanding
Hard to say how long it takes for one call. I usually cut and drill my blanks ahead of time. Once the blank is ready I have pot calls right at around 30 minutes on the lathe. It gets much quicker with time. About 15 minutes for a 1 piece striker.
Josh
When I get to rolling on the lathe, 6 minutes from start to finish on a striker. A pot can be done in about 30
Prep time on a pot is right around 7-10 minutes. Lathe time is 20 minutes. I usually break up my process and don't do it all at once to reduce the possibility of a pot reacting to too much heat.
Just let me get this straight. I'm not a pot or box call maker or anything but I just like reading this stuff.
You guys can take a square piece of wood, turn it, and have it completely assembled with just waiting for the glue to dry in two hours? That just is amazing to me. Damn impressive.
Quote from: compton30 on March 28, 2018, 06:20:03 PM
Just let me get this straight. I'm not a pot or box call maker or anything but I just like reading this stuff.
You guys can take a square piece of wood, turn it, and have it completely assembled with just waiting for the glue to dry in two hours? That just is amazing to me. Damn impressive.
That's up to $60 hr. Of work
Quote from: compton30 on March 28, 2018, 06:20:03 PM
Just let me get this straight. I'm not a pot or box call maker or anything but I just like reading this stuff.
You guys can take a square piece of wood, turn it, and have it completely assembled with just waiting for the glue to dry in two hours? That just is amazing to me. Damn impressive.
That's for the turning part. Then the finish can take a while depending on the kind you use. Right now I'm using an acrylic which takes multiple coats. Then I glue in my sound board and keep it under pressure for at least 12 hours. Then I apply the playing surface and keep it under pressure for around 24 hours to insure the glue sets up properly before I condition and play it. But yes in general about two hours from raw boards to a pot and striker both. I don't buy blanks at this time I buy raw lumber and cut my own blanks out. The slowest part is having to stop alot to measure when your getting close to your depths and widths.
Sent from my SM-N920V using Tapatalk
Quote from: southern_leo on March 28, 2018, 08:45:33 PM
Quote from: compton30 on March 28, 2018, 06:20:03 PM
Just let me get this straight. I'm not a pot or box call maker or anything but I just like reading this stuff.
You guys can take a square piece of wood, turn it, and have it completely assembled with just waiting for the glue to dry in two hours? That just is amazing to me. Damn impressive.
That's for the turning part. Then the finish can take a while depending on the kind you use. Right now I'm using an acrylic which takes multiple coats. Then I glue in my sound board and keep it under pressure for at least 12 hours. Then I apply the playing surface and keep it under pressure for around 24 hours to insure the glue sets up properly before I condition and play it. But yes in general about two hours from raw boards to a pot and striker both. I don't buy blanks at this time I buy raw lumber and cut my own blanks out. The slowest part is having to stop alot to measure when your getting close to your depths and widths.
Sent from my SM-N920V using Tapatalk
But in terms of start to finish, not counting the wait time for things to dry, it takes about 2.5-3 hours total for a pot call to be made? For whatever reason I thought it took a lot longer. Just impressed.
Once I have my blank cut and drilled, about 45 minutes on the lathe. Probably half of that time is measuring.
Take me two days from start to finish..that's from a block of wood to a call you can take hunting.
Quote from: compton30 on March 28, 2018, 06:20:03 PM
Just let me get this straight. I'm not a pot or box call maker or anything but I just like reading this stuff.
You guys can take a square piece of wood, turn it, and have it completely assembled with just waiting for the glue to dry in two hours? That just is amazing to me. Damn impressive.
From taking a board, squaring it, sanding it, laying out and drilling holes, total turning time, sand, finish, ready for glue I was averaging 35 minutes over the weekend. Lol. NOW, I break my process up and like to let the pot rest at different stages in that but.... yeh. Lol. The crazy thing is I know guys much faster and just as accurate as I am.
That's amazing Paul. it takes me 35 minutes just to sand mine..let alone the other..how do you sand? what grits etc.
Sand on the lathe, low speed. 150, 220, 320, 400, 600. If you got a rough spot hit it with 100 first. Keep sand paper fresh ( its cheap), let it do the work, not you. That'll keep the heat down and keep the pot from warping.
Quote from: ridgerunner on June 26, 2018, 08:29:04 AM
That's amazing Paul. it takes me 35 minutes just to sand mine..let alone the other..how do you sand? what grits etc.
That's way too much time! Your heating up the wood. And most likely sanding the face Grain and end grain in an uneven rate. Use only the top shelf sand paper cheap sand paper has poor grit quality. After you finish cut (shear scrape) the wood. You should not have to go below 150 grit except on some because of tear out. 150/180/220/320 is generally sufficient on most woods. Dark woods may need finer 400/600. The human eye can't really see a scratch pattern finer than 320 on most woods.
Quote from: mmclain on October 16, 2018, 10:47:10 PM
Quote from: ridgerunner on June 26, 2018, 08:29:04 AM
That's amazing Paul. it takes me 35 minutes just to sand mine..let alone the other..how do you sand? what grits etc.
That's way too much time! Your heating up the wood. And most likely sanding the face Grain and end grain in an uneven rate. Use only the top shelf sand paper cheap sand paper has poor grit quality. After you finish cut (shear scrape) the wood. You should not have to go below 150 grit except on some because of tear out. 150/180/220/320 is generally sufficient on most woods. Dark woods may need finer 400/600. The human eye can't really see a scratch pattern finer than 320 on most woods.
No i don't think i'm heating the wood up Matt or taking too much time.... I'll post a pic of one of my finished calls. then you can critique it for me.